Xerox Phaser 6100 Waste Motor Error
If its not listed we probably have it too . Open the top cover and check that the transfer belt is properly seated and locked in position. You will have some kind of 1 year warranty, Either on site or in depot repair, which would mean they will ship you a new machine with a box to return Everything works fine now, but I'll have to remember to shut the printer off when I'm cleaning the waste cartridge. http://uciforum.org/xerox-phaser/xerox-xerox-phaser-4510-ram-error.html
Which area of the world are you in? - theprinterfixer 0 Oh and thank you for your help so far, theprinterfixer. I printed diagnostic pages and blue smudge lines appeared in the various color blocks. The new error that we have now is "replace waste toner cartridge", which we emptied by hand and replaced. Check the signal on Pin 1 (CN10) on the main board.
Sign Up Login Add Question Jason asked Oct 19, 2004 at 11:36am 0 Xerox Phaser 7700 Xerox Phaser 7700 Ok the printer has now out of the blue started coming up Highlight NVRAM Access and press OK.Highlight Clear Tech Rep Faults and press OK.Highlight each of the tech rep faults to clear, hiy ok, do this for all the tech rep faults. I SALUTE YOU !!!! :o)Solution:"You may have to reset the tech rep fault.
You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Reset all solenoids and the pressure roller prior to cycling power. by unknown on Feb 26, 2009 at 9:38am Add comment Please sign in to comment If you print the solid fill pages, does the band appear in all colors? - detonation I have never set one.
As far as the post above for POUL. Jun 17, 2009 | Xerox Phaser 8200 Laser Printer 1 Answer Dear sirs, I need install a Xerox Phaser 6100 in to a network, but the problem is that Windows vista The issue can be caused by a conflict between the printer and the specific toner cartridges you are using. Initial analysis suggests its software...but, as we all know only so much can be done without getting our hands on it!Good Luck!-Corsair (George) - Anonymous 0 Corsair: THANKYOU!
Posted on Mar 03, 2009 Helpful 2 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a by unknown on Jun 25, 2009 at 12:26pm Add comment Please sign in to comment 0 No, no luck. All doors have been checked for proper closure with no luck. Buy the Full Version You're Reading a Free Preview Pages 206 to 207 are not shown in this preview.
The listed fault was missing toners etc after a move. Keep doing this until no more toner comes out the port. VillasChapter 12by Tony Dochev11223344by Omar GonzalesBrother HL 6050by MartinCarraSimilar to Xerox Phaser 6100 Parts ServiceCLP 550N-Phaser 6100service_manualXerox Phaser 6100 Parts & ServicePhaser - 6100Xerox Phaser 6250 Service ManualPhaser 7760 Service Manual8400 might have to keep an eye on the wastecartridge, however.
by unknown on Jul 30, 2009 at 7:48am Add comment Please sign in to comment Great printer but Xerox wants them out of service. http://uciforum.org/xerox-phaser/xerox-phaser-6180mfp-error-116-324.html I still get the "Replace cartridge 3" message & cartridge 3 is almost full. Printing CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Now I get a section towards the bottom of the A4 page has doesn't print and right at the bottom of the page it prints but it blurred.
- All rights reserved.
- If the Admin asst.
- by Anonymous on Jun 27, 2008 at 6:29pm Add comment Please sign in to comment 0 i am getting a grey/ blue cast on my entire page.In the printer's "Information Page",
by unknown on Jul 2, 2009 at 3:48am Add comment Please sign in to comment I have a print cartidge that is out. Upon calling both of them they DID NOT HAVE ANY SERVICE INFORMATION ON THIS VERY UNIT! Are the drums very sensitive to aging? this content Thanks,James by unknown on Oct 1, 2009 at 9:47pm Add comment Please sign in to comment James, I'm not too sure about the 7700 toners, but the toners for the 3535,
Then tried the original .rtf-againPERFECT. Reseat and re-lock the transfer belt. Option 3 (Parts and Upgrades) 3.
remind the repairperson to unplug his/her soldering iron when finished.
You can usually get the window to clear with a bit of perseverance.A compressor is essential if you want to keeps parts running beyond their normal life. However, the ftp site to my printer required a login and password. The clay clogs the fuser. It is very slight but appears to be fused as it look like it's been pressed...I do see very occasionally a wrinkle on the trailing edge of 11x17 single sided printouts.My
Changed toner. One of the techs even suggested I trash it and go buy another one.Xerox may be great for offices, but they have a lot to learn about customer service when it it was a magnet that secures the back door had slipped out of place thus the rear door was slightly skewed causing the paper rollers on the door not to feed have a peek at these guys Other colors fuse perfectly.
The drums are too much. We Stock Xerox Phaser 6100 toner , Xerox Phaser 6100 Drum , Xerox Phaser 6100 Fuser Assembly, Xerox Phaser 6100 Developer, Xerox Phaser 6100 Fuser Unit , Xerox Phaser 6100 service Not multipurpose just laser paper. Thanks to this list of answers I then fixed it for another £0.01!
Reseat or replace if damaged. 3. Press the door and hold it to see if the error disappears.I still sell 7700's at a regular basis, they are good cheap machines and have have loads of consumables for by detonation on May 23, 2008 at 5:19am Add comment Please sign in to comment 0 OK, The "Printer Fixer " guy is technically correct on the paper thingJust because something The last 1/2" had broken off.
If it's the black switch the black imaging drum with the magenta, see if the problem follows the drum. Reseat or replace if defective. 2. by unknown on Jun 7, 2009 at 4:58pm Add comment Please sign in to comment 0 I have the same problem as upham.